* Allow 64-bit vectors and implement for interpreter
The AArch64 backend already supports 64-bit vectors; this simply allows
instructions to make use of that.
Implemented support for 64-bit vectors within the interpreter to allow
interpret runtests to use them.
Copyright (c) 2022 Arm Limited
* Disable 64-bit SIMD `iaddpairwise` tests on s390x
Copyright (c) 2022 Arm Limited
This adds full support for all Cranelift SIMD instructions
to the s390x target. Everything is matched fully via ISLE.
In addition to adding support for many new instructions,
and the lower.isle code to match all SIMD IR patterns,
this patch also adds ABI support for vector types.
In particular, we now need to handle the fact that
vector registers 8 .. 15 are partially callee-saved,
i.e. the high parts of those registers (which correspond
to the old floating-poing registers) are callee-saved,
but the low parts are not. This is the exact same situation
that we already have on AArch64, and so this patch uses the
same solution (the is_included_in_clobbers callback).
The bulk of the changes are platform-specific, but there are
a few exceptions:
- Added ISLE extractors for the Immediate and Constant types,
to enable matching the vconst and swizzle instructions.
- Added a missing accessor for call_conv to ABISig.
- Fixed endian conversion for vector types in data_value.rs
to enable their use in runtests on the big-endian platforms.
- Enabled (nearly) all SIMD runtests on s390x. [ Two test cases
remain disabled due to vector shift count semantics, see below. ]
- Enabled all Wasmtime SIMD tests on s390x.
There are three minor issues, called out via FIXMEs below,
which should be addressed in the future, but should not be
blockers to getting this patch merged. I've opened the
following issues to track them:
- Vector shift count semantics
https://github.com/bytecodealliance/wasmtime/issues/4424
- is_included_in_clobbers vs. link register
https://github.com/bytecodealliance/wasmtime/issues/4425
- gen_constant callback
https://github.com/bytecodealliance/wasmtime/issues/4426
All tests, including all newly enabled SIMD tests, pass
on both z14 and z15 architectures.
PR https://github.com/bytecodealliance/wasmtime/pull/3187 introduced a
change to the write_to_slice and read_from_slice routines in
data_value.rs that switched byte order on big-endian systems:
the code used to use native byte order, and now hard-codes
little-endian byte order.
Fix by using native byte order again.
* cranelift: Add stack support to the interpreter
We also change the approach for heap loads and stores.
Previously we would use the offset as the address to the heap. However,
this approach does not allow using the load/store instructions to
read/write from both the heap and the stack.
This commit changes the addressing mechanism of the interpreter. We now
return the real addresses from the addressing instructions
(stack_addr/heap_addr), and instead check if the address passed into
the load/store instructions points to an area in the heap or the stack.
* cranelift: Add virtual addresses to cranelift interpreter
Adds a Virtual Addressing scheme that was discussed as a better
alternative to returning the real addresses.
The virtual addresses are split into 4 regions (stack, heap, tables and
global values), and the address itself is composed of an `entry` field
and an `offset` field. In general the `entry` field corresponds to the
instance of the resource (e.g. table5 is entry 5) and the `offset` field
is a byte offset inside that entry.
There is one exception to this which is the stack, where due to only
having one stack, the whole address is an offset field.
The number of bits in entry vs offset fields is variable with respect to
the `region` and the address size (32bits vs 64bits). This is done
because with 32 bit addresses we would have to compromise on heap size,
or have a small number of global values / tables. With 64 bit addresses
we do not have to compromise on this, but we need to support 32 bit
addresses.
* cranelift: Remove interpreter trap codes
* cranelift: Calculate frame_offset when entering or exiting a frame
* cranelift: Add safe read/write interface to DataValue
* cranelift: DataValue write full 128bit slot for booleans
* cranelift: Use DataValue accessors for trampoline.
* Rewrite interpreter generically
This change re-implements the Cranelift interpreter to use generic values; this makes it possible to do abstract interpretation of Cranelift instructions. In doing so, the interpretation state is extracted from the `Interpreter` structure and is accessed via a `State` trait; this makes it possible to not only more clearly observe the interpreter's state but also to interpret using a dummy state (e.g. `ImmutableRegisterState`). This addition made it possible to implement more of the Cranelift instructions (~70%, ignoring the x86-specific instructions).
* Replace macros with closures
As discussed in #2251, in order to be very confident that NaN signaling bits are correctly handled by the compiler, this switches `DataValue` to use Cranelift's `Ieee32` and `Ieee64` structures. This makes it a bit more inconvenient to interpreter Cranelift FP operations but this should change to something like `rustc_apfloat` in the future.
